Scarlet Witch Hex Powers (Tutorial)

A week before going to MarsCon I decided to come up with something to look like Scarlet Witch’s hex powers (not really sure what to call this particular prop: Hex powers? Magic orbs? Glowing chaos magic?). I’m not sure why I always decide to do these things at the last minute, but there you go.

To my surprise, they turned out pretty well, and so I thought I’d share a tutorial with you all!


Photo of the Hex Powers in action! Photo by Scott Saniti.

What you’ll need:

  • 2 red battery-operated LED tea lights
  • 2 clear tea light candle casings
  • Red tulle/netting (about 1/3 yard)
  • 2 sheets of 8 1/2″ x 11″ red cellophane sheets
  • 1/2 yard of red gathered lace trim
  • Mod Podge
  • Red glitter
  • 2 ring blanks
  • Piece of 8 1/2″ x 11″ paper
  • Black Sharpie
  • Hot glue gun and hot glue sticks
  • Small paintbrush
  • Dressmaker pins
  • Sharp scissors

Most of the items I had on-hand because I hoard craft supplies, but I’d say all of these could be found at any craft supply store (with maybe the exception of the LED tea lights).

The first (and potentially optional) step is to add glitter to the LED tea lights. I did this so that they blended in more, and also to reflect some of the light from the LEDs. The LED lights I purchased were in a pack of 36 from Amazon. They’re really bright, and the color is good! They’re about the size of a US quarter, and run on two cell batteries (included).

Using a small paintbrush, paint a coat of Mod Podge onto the top of the LED tea light (avoiding getting any on the bulb part of the light, if possible). Sprinkle red glitter over the Mod Podge and shake off any excess. Allow the Mod Podge to dry and add another coat of Mod Podge and glitter if you think the tea lights need more coverage. After the Mod Podge is dry, coat the glitter with a layer of Mod Podge to seal in the glitter. I used the Extreme Glitter Mod Podge because I like the extra sparkle. Allow the Mod Podge to dry.


The next step is to create a template for the tulle and cellophane. I basically just folded a piece of 8 1/2″ x 11″  paper into fourths and sketched out a spiky design, and then cut it out. This can look however you like, but the above photo is how mine looked.

I bought a pack of multicolored cellophane sheets from Amazon, but I only needed the two sheets of red cellophane for this project. Lay the red cellophane over a piece of white paper (it makes seeing what you’re doing a lot easier) and then lay the template over that. Use a black Sharpie to trace the template (it doesn’t need to be super accurate). Cut out the template and make sure to trim off any of the black lines from your tracing. Repeat the process for the second cellophane sheet.

Next step is to cut out tulle from your template. The tulle I used was glittery, but you can use regular tulle. I folded my tulle in half and used dressmaker pins to pin the template to the tulle, and then cut it out. Again, it doesn’t need to be perfect. Repeat the process again, and when you’re finished you should have four tulle “bursts.”

Add a small dot of hot glue to the center of one cellophane burst and then lay one tulle burst over the dot of glue, but slightly askew. Your goal is to sort of “stagger” the tulle and cellophane so that the spikes are not perfectly lined up. Once the glue sets, flip over the cellophane and tulle. Add another dot of hot glue and lay the other tulle burst over the dot of glue (again, slightly askew). Once the glue sets, you should have a cellophane burst sandwiched between two tulle bursts. Repeat this process for the other set.

For this part, you’ll need some sort of shallow, clear, plastic container that’s just a little bigger than the LED tea light. The ones I used were plastic “casings” from some tea candles I bought from Target (like these). I took out the candles, and then washed the plastic casings with soap and water to remove any wax residue.

On the bottom of the casing, add a dime-sized dab of hot glue in the center, then place the casing onto the center of the tulle and cellophane burst. You’ll basically be covering up the dab of hot glue from the previous step. Allow the glue to set.

Add a strip of hot glue around the base of the casing and then bunch the cellophane and tulle around it until the glue sets. This will adhere one layer of tulle and the layer of cellophane to the casing.


Add a couple dots of hot glue on the cellophane layer and press down the outer tulle layer and hold it in place until the glue sets. Rotate, and repeat the process until the outer tulle layer is tacked down to the cellophane layer.

The next step is to add red gathered lace trim along the bottom edge of the casing. The pattern of the lace is not important – but make sure it’s gathered lace and not flat lace. Add a line of hot glue along the bottom edge of the casing and gently lay the lace along the glue. Try not to press the lace down with your finger because the glue might seep through. Continue until the lace is glued all around the bottom edge (and overlap about 1/2″) before trimming. The purpose of the lace is to keep the tulle and cellophane upright, and it also hides any flaws in the gluing process from the previous steps. It also looks really cool, I think.

Ring blanks are basically rings that have a flat metal piece attached to the top where a stone or other object can be glued to create jewelry. For this, the shape of the metal piece isn’t important, so use whatever kind of ring blanks you want. I used these.

Add a glob of hot glue to the flat metal piece and press it into the center of the underside of your casing. Hold it in place until the glue sets.


Unscrew the top off of the LED tea light and remove the two batteries. Because you’ll be attaching the bottom piece to your casing with hot glue, it’s a good idea to remove the batteries beforehand so there’s no chance of the batteries exploding. (Safety first!)

Add hot glue to the underside of the bottom piece of the LED tea light and press it into the inside center of the casing. Allow the glue to set, and repeat for the second casing. Once the glue is set and cooled, the batteries can be inserted and the top can be screwed back on.

You now have hex powers! Having the LED tea light inside a casing allows you to turn the lights on and off, and also replace the batteries when necessary. Because the hex powers are on rings, you can wear them and move your hands however you like (go crazy and wave your hands around!) and it looks super cool.


One thought on “Scarlet Witch Hex Powers (Tutorial)

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s